A truck phone mount has a harder job than a car mount. Washboard gravel, two-track, job sites, cold-soaked plastic dashes and a phone that gets bigger every year. Most of what gets sold as a phone holder for a truck was never engineered for any of it: suction cups let go in the heat, adhesive pads peel off textured dashes, and vent clips sag under a large phone in a case.
Mountech builds the other kind. Our dash mounts are designed around one specific truck interior and attach at factory hardware locations instead of relying on glue or suction. Above the base, everything runs on the 1" ball standard, so a single cell phone mount for a truck can carry a phone today and a camera or a handheld tomorrow by swapping the head.
This page covers how vehicle-specific phone mounts differ from universal ones, which cell phone mounts for trucks we build for each make, the mount types we offer, and how to choose between them. If you already know your truck, start with your vehicle or browse all vehicle solutions.
A universal holder is a compromise in every truck it goes into. A vehicle specific phone mount is engineered for exactly one interior, so it lands where your hand already goes, keeps the screen out of your sightline, and doesn't cover a vent, a switch panel or the infotainment screen.
That's the difference between a phone mount for trucks and a phone mount that happens to fit in one. Our vehicle-specific dash mounts pick up existing hardware locations in your truck, which is why the F-150 part and the Silverado part are genuinely different parts rather than the same clamp in two boxes.
Pick your make, model and year and we'll show you only what fits.
Direct-fit kits are available now for Ford, Jeep, Chevrolet, GMC and Toyota, with more in development. Start with your make below, then read on for the model and year detail.
The F-150 phone mount isn't one part, it's four. The dash changed with every generation, so a 2018 F-150 phone mount and a 2025 F-150 phone mount are genuinely different platforms — buying by year is how you avoid a mount that almost fits.
Super Duty, Ranger and Bronco each get their own direct-fit kit. For the long version, read the ultimate Ford F-150 phone mount.
Our Tacoma dash mount fits 2024 and newer trucks with the 8" screen and puts the phone at the top of the center stack instead of hanging off a vent. It is a true Tacoma dash mount, not a universal holder with a Toyota sticker on it.
A 3rd gen Tacoma phone mount, Tundra phone mount and 4Runner phone mount are on the bench with our engineering team. Until they land, the heavy duty vacuum cup base plus a socket arm runs the same head in an older Tacoma or a 4Runner.
The Jeep phone mount question is really two questions, and one kit answers both: our dash mount for the JL Wrangler (2018-2023) and Gladiator (2020-2023). It picks up the factory dash hardware, so the mount doesn't move when the doors and roof do.
Wrangler and Gladiator owners tend to add a second head for a camera or a light, which the 1" ball system handles without buying a second base.
The Silverado phone mount and the Sierra phone mount share a part: our dash mount for the 2019-2023 Silverado 1500 and Sierra 1500 with the large dash cubby, which turns that cubby into a solid mounting platform instead of a place your phone slides around in.
Mid-size trucks get their own kit, the 2023+ Colorado and Canyon dash mount. 2500 and HD applications release through the Chevrolet and GMC collections.
We are not going to sell you a Ram 1500 phone mount, a Nissan Frontier phone mount, a Honda Ridgeline phone mount or a Cybertruck phone mount that we haven't engineered for that truck. Those kits are in development, and these collections will tell you the moment they land.
You can still run the same hardware today. Start with the heavy duty vacuum cup base or an AMPS-pattern ball mount base on an existing bracket, add a socket arm, and finish with the holder you want. When the direct-fit base for your truck arrives, the arm and the holder carry over.
Solid = shipping today. Dashed = in development; open the collection to be notified when it releases.
Four pieces make up every Mountech setup: a base that attaches to the truck, an arm that positions the phone, a head that holds it, and the 1" ball that joins them. Here is what each one does and when to choose it.
The dash mount is the foundation of a proper truck phone holder. It attaches to your truck at factory hardware locations, which is what lets it carry a large phone over rough ground without creeping, sagging or letting go the way an adhesive phone holder for a truck dashboard does.
Because the base is vehicle-specific, the phone ends up in a place you chose rather than a place a clamp allowed: high on the stack, clear of the vents, out of the airbag path and inside easy reach.
Every Mountech base ends in the same 1" (25.4mm) ball, and every arm ends in a socket that clamps onto it. That single standard is what makes a ball mount phone holder so useful in a truck: change the angle, change the height, or change the head entirely without touching the base.
Bases come in 2-bolt and 4-bolt AMPS patterns, so they bolt to our vehicle-specific platforms or to anything else with the standard hole spacing. Our 1" ball mounts and socket arms also work with any other mounting platform built around a 1" ball.
Two heads, same 1" ball. The magnetic, MagSafe-compatible holder is the fastest one-handed option in a truck: the phone lands on the magnet and comes off in one motion, no arms to open. The standard cradle holder grips mechanically and fits phones up to 3.4" wide and 0.5" thick, which covers most large phones in a case.
Magnets and modern phones get along better than most people expect. If you want the detail, we wrote about why MagSafe made phone mounting better.
We spent years telling people not to buy a windshield phone mount, because the cheap ones fail in the heat and take your phone with them. Then we built one worth owning: a heavy duty vacuum cup base with a locking cam that pulls a real vacuum against glass and finishes in the same 1" ball as everything else.
It is the right answer when a direct-fit dash mount doesn't exist for your truck yet, when you move one mount between vehicles, or when you need a temporary position for a trip. Check your state's rules on windshield placement before you commit to that spot.
The best phone mount for a truck is the one engineered for that truck. Find your make, model and year first; phones change every two years, but the base you bolt in should outlive several of them.
Pavement and a light phone forgive a lot. Washboard, trail chatter and a large phone in a heavy case do not. If your truck sees rough ground, choose a hardware-mounted base and a short arm; length is leverage, and leverage is what shakes.
Magnetic if you want one-handed on and off, cradle if you run a thick case or no magnet ring. Then look at where the charge cable lands and whether the phone blocks a vent, a switch or your view down the hood.
If your truck doesn't have a direct-fit kit yet, or you want a second position for a camera or a handheld, build the mount yourself. Pick the base, the arm length and the head; they all meet at the same 1" ball, so any combination works.
Phone mounts themselves are legal in every U.S. state. What states regulate is where the mount can sit and whether you can hold or touch the phone while driving. Most restrictions apply to windshield placement rather than to dashboard phone mounts, which is one reason a vehicle-specific dash mount is the safest default. Check your own state's vehicle code before choosing a windshield position.
California allows a windshield mount only in specific areas: a 7-inch square in the lower corner farthest from the driver, or a 5-inch square in the lower corner nearest the driver, and it can't block the driver's view. Anywhere else on the glass is out. A dash mount avoids the question entirely, and rules differ by state, so confirm yours.
Yes. The magnets used in phone mounts, including MagSafe-compatible ones, don't harm modern phone storage, batteries or screens. Phone storage is flash memory, not magnetic media. The one thing to watch is credit cards and hotel keys stored in a wallet case, since magnetic stripes can be affected.
It depends on the stack. A magnetic mount grips the nearest magnetic surface, so a battery pack sandwiched between the phone and the mount reduces holding force and adds weight and leverage at the same time. In a truck on rough ground, run a cradle-style holder or plug in with a cable and skip the pack.
They're rarely a danger to the phone, though blowing hot air across it in summer doesn't help battery temperature. The bigger issues are practical: vent blades were not designed to carry weight, a large phone in a case sags or pops loose over bumps, and the mount blocks the vent you wanted. In a truck, a dash mount is a far better use of the same space.
Mountech doesn't build a cup holder phone mount today. If you're shopping for one, look for a base that expands against the cup holder wall rather than a friction fit, the shortest gooseneck you can live with, and a head that runs on a standard 1" ball so you're not locked into one brand. Be honest about the trade-off first: a truck cup holder phone mount sits low, out of your sightline, and costs you a cup holder. A vehicle-specific dash mount usually solves the same problem better.
Warm the adhesive first with a hair dryer on low for a minute or two, then work dental floss or fishing line behind the pad and saw side to side to break the bond. Remove the residue with an adhesive remover made for automotive interiors, applied to a cloth rather than sprayed on the dash, and test it in a hidden spot. Textured dashes take patience. This is exactly the mess a bolt-in dash mount avoids.
Yes. Mountech 1" SpinLok ball mounts and socket arms work with any mounting platform that also uses a 1" ball mount, so you can mix our bases, arms and heads with hardware you already own.
Our vehicle-specific dash mounts are designed to use existing hardware locations in your truck's interior rather than adhesive, suction or new holes. Installation steps vary by vehicle, so check the product page for your specific truck and year, and see our installation guides for walkthroughs.
Our universal cradle phone holder fits phones up to 3.4" wide and 0.5" thick, which covers most large phones in a standard case. The magnetic, MagSafe-compatible holder works with any phone that has MagSafe or a magnet ring on the case.
All Mountech products are warrantied against manufacturing defects and material failures for the entire life of the product, limited to the original purchaser with proof of purchase. Normal wear and abuse aren't covered. Contact us and we'll take care of it, or read more on our FAQ page.
Lifetime Warranty
Mount Without Compromise
Find the truck phone mount engineered for your make, model and year, and back it with our Buy It For Life guarantee.
